You are currently viewing Common Plumbing Problems and How to Fix Them

Common Plumbing Problems and How to Fix Them

  • Post author:
  • Post published:
  • Post category:General

Dripping Faucet

A dripping faucet is a common plumbing problem that can be both annoying and wasteful. The constant dripping can lead to increased water bills, and the sound can be quite bothersome. Fortunately, fixing a dripping faucet is often a simple task that you can do on your own. Broaden your understanding of the topic by visiting this suggested external site. There, you’ll find valuable details and supplementary information that will enrich your reading experience. plumber adelaide, don’t miss out!

  • Start by turning off the water supply to the faucet. This is usually done by closing the valve underneath the sink.
  • Next, remove the handle of the faucet using a screwdriver or an Allen wrench, depending on the type of faucet.
  • Once the handle is removed, you will see a cartridge or a washer. These are the parts that are typically causing the leakage.
  • Inspect the cartridge or washer for any signs of damage or wear. If they appear worn out or damaged, replace them with new ones.
  • Reassemble the faucet by putting the handle back on and turning the water supply back on.
  • If the problem persists even after replacing the cartridge or washer, it might be best to consult a professional plumber to assess and fix the issue.

    Clogged Drain

    A clogged drain is another common plumbing problem that can disrupt your daily routine. Whether it’s a clogged sink, shower, or toilet, it’s important to address the issue promptly to prevent further damage or flooding.

  • For a clogged sink or shower drain, try using a plunger. Make sure to cover the overflow drain with a rag or tape to create a tight seal. Then, plunge the drain vigorously several times to create pressure and dislodge the clog.
  • If the plunger doesn’t work, you can try using a plumbing snake. Insert the snake into the drain and rotate it while pushing it further in. This should help break up the clog and allow the water to flow freely.
  • For a clogged toilet, start by using a plunger. Place the plunger over the drain hole and push down firmly, then lift it up quickly. Repeat this motion several times until the water starts draining.
  • If the plunger doesn’t work, you may need to use a toilet auger. Insert the auger into the toilet bowl and rotate the handle while pushing it in. This should help break up the clog and restore proper flow.
  • If your attempts to unclog the drain are unsuccessful or if you’re dealing with a recurring clog, it’s advisable to call a professional plumber to assess and resolve the issue.

    Running Toilet

    A running toilet is not only a nuisance but can also waste a significant amount of water. Addressing this problem promptly can help save water and prevent potential damage to your toilet and plumbing system.

  • Start by removing the tank lid and inspect the components inside. Look for any worn-out or damaged parts.
  • Check the flapper valve, which is responsible for controlling the water flow from the tank to the bowl. If it’s warped or damaged, it may not seal properly, causing the toilet to run continuously. Replace the flapper valve if necessary.
  • Another common culprit for a running toilet is a faulty fill valve. This valve controls the water level in the tank. If it’s malfunctioning, it can lead to continuous water flow. Consider replacing the fill valve if needed.
  • Lastly, check the float and adjust it if necessary. The float is responsible for shutting off the water flow once the tank is full. If it’s set too high, it can cause the water to continuously run. Follow the instructions provided with the toilet to adjust the float correctly.
  • If you’ve tried these steps and the toilet continues to run, it’s recommended to seek professional assistance to diagnose and fix the underlying issue.

    Low Water Pressure

    If you’re experiencing low water pressure in your home, it can greatly affect your daily activities, such as showering and washing dishes. Low water pressure can be caused by various factors, including clogged pipes or an issue with the municipal water supply. Here are a few steps you can take to troubleshoot low water pressure:

  • Check all faucets and fixtures in your home to determine if the low water pressure is isolated to just one area or if it’s a widespread issue.
  • If the low water pressure is specific to one faucet or fixture, remove the aerator and clean it thoroughly. A clogged aerator can restrict water flow and cause low pressure.
  • If the low water pressure is affecting multiple faucets or fixtures, it may be a sign of a larger issue, such as a clog in the main water line or a problem with the water pressure regulator. In such cases, it’s best to call a professional plumber to diagnose and resolve the problem.
  • Consider contacting your local water utility company to inquire about any known issues with the municipal water supply that could be causing the low water pressure.
  • Addressing low water pressure requires proper diagnosis, and it’s important to consult a professional plumber if the problem persists or worsens.


    Plumbing problems can be frustrating, but with the right knowledge and tools, many common issues can be resolved without the need for professional assistance. However, it’s crucial to know your limits and seek professional help when necessary. Regular maintenance and proactive measures can also help prevent plumbing problems and keep your plumbing system running smoothly. To discover additional and complementary information on the subject covered, we’re committed to providing a rich educational experience.!

    Delve deeper into the theme with the selected related links:

    Find additional insights here

    Investigate this topic further

    Explore this informative research

    Common Plumbing Problems and How to Fix Them 1